Honda CX 500 Forum banner

parts

  1. 82 CX Custom for sale 300$ MN

    Selling and Buying Forum
    Hello, I have a 1982 CX500 Custom for sale for 300$ The engine does not run. It was running fine until the copper bearings broke last year. The engine has stayed in a warm garage all winter. I bought the CX at the beginning of last year and learned to ride, now that its riding season I dont...
  2. Heck Of A Deal - 1979 CX500 Parts Bike

    Selling and Buying Forum
    While doing some horsetrading last week I ended-up with a 1979 CX500 parts bike. The engine will move and most of it is there except for tank and bodywork, seat, handlebars. If you need the parts, this is it for you! $100.00 or trade me something. I have pix. e-mail me at...
  3. Searching for an oil filter washer/seat

    General Discussion
    I think I lost my old one during a distracted oil change cuz when I went back in there to change the filter and oil last week, the washer/seat was gone. It's this part: SEAT, OIL FILTER SPRING 15414-300-000 https://www.partzilla.com/product/honda/15414-300-000 I'm willing to pay. I just don't...
  4. Wanted: Good CX500 Engine Block

    Selling and Buying Forum
    Hi there, I am on the hunt for a decent, running CX500 CDI engine with good compression. Aesthetics aren't overly important as I plan to strip and paint it however I would prefer confirmed running etc. I also have the front and rear cover, clutch, gearbox and stator etc.. so really just the...
  5. FS 83 CX650 Custom for repair or parts - backfires and power loss - in New Hampshire

    Selling and Buying Forum
    SOLD - For Sale $400 OBO - Parts or Repair - Honda 83 CX650 Custom - 23,000 miles, black , ran great until two days ago, had to make a hard stop with quick downshifts to help stop and afterwards lots of back firing and power loss rough idle but still drives. Not sure what is wrong and no tools...
  6. Part identification.

    Technical Help Forum
    Hi All, Can you please help me identify these parts. I have replaced my entire front end on the bike as well as modify the frame heavily, I want to ensure these parts are what I think they are. Thanks,
  7. Carburetor missing part, can't find replacement

    Technical Help Forum
    Earlier this week while riding my CX, my bike starting bogging down dramatically. I could barely reach 20mph. I have had this happen before and I have usually fixed it by thoroughly cleaning my carbs so when I made it home I removed them and began to disassemble. Before I got to far I realized...
  8. GL650 for parts in Columbus, Ohio

    Where Can I Find...
    Howdy y'all, I was passing through my old haunt 2 weeks back and spotted a complete (from what I could see) GL650 in a moto parts place in Columbus, Ohio. I saw both hard bags, complete fairing with windscreen, motor, wheels, etc. I meant to post this earlier but had a brain fart. It's at a...
  9. WTB: Odd carburetor gaskets

    Selling and Buying Forum
    Does anyone have/ know where I can find just a few odd carburetor gasket parts? I'm looking for just odd ones and I don't want to buy the whole kits. I mostly need: accelerator pump boot and needle washer/oring combination. Let me know!
  10. Coolant system Parts Sourcing UK

    Technical Help Forum
    Hi Guys, out of interest, does anyone know where in the UK I can source the copper washer, 6mm end bolt and thrust washer for the impeller assembly on eBay or something (links would be great :D ) Typing in the OEM part number )(or the one I have at least) on eBay only gives me USA parts with...
  11. Looking for a longer 12mm flange bolt than stock

    Where Can I Find...
    Hey there! I have a custom CX500 that was recently completed. I put a few hundred miles on it so far, and noticed recently that the nut on the 12mm flange bolt below the engine (picture below) had rattled off. I suspect this is because we put a custom exhaust on the bike, which is mounted on...
  12. 1980 CX500 Custom Parts

    Selling and Buying Forum
    I've got some extra parts laying around I would like to get rid of. Shoot me reasonable offers. Buyer pays shipping. H-Box with some yamaha mufflers the PO welded on (will be trying to remove)
  13. Michigan. Parts for sale. GL500. Fairing, mufflers, fork tubes...

    Selling and Buying Forum
    Guy in my area has these for sale. Anyone need this stuff? I started to buy it but running out of storage. Again: NOT my stuff. I've got for a 1982 Honda GL500i Interstate...many parts same as CX500...the full front stock Honda fairing, exhaust pipes plus a full set of refurbished gold...
  14. BEARING B, CONN ROD 13216-415-013 Help

    Technical Help Forum
    Hello all, I have recently purchased my first CX500 C 1982 and am digging deep. The engine had some worn connecting rod bearings and crank shaft journals. It looks like a new shaft is in order and new bearings as well. On ebay there are a number of options for the Crank shaft with size B...
  15. 83 Honda GL650

    Selling and Buying Forum
    Hey guys. I have a lot of stock parts for the GL650 i'm looking to unload. I am located in Philadelphia. Will ship. All prices aren't firm. Front Wheel with break rotor - $60 Rear Fender Assembly - $75.00 Forks - $100.00 Carbs - $100.00 Rear Shock - $100.00 Rear Turn Signals - $40.00 Triple...
  16. In need of some assistance/grievance/cash/sorrow/condolences..

    Selling and Buying Forum
    In need of some assistance/cash/help!! I need help. Trying to get to Northern California for the summer and need to sell some of my things, a new bike, cage, or similar!! my lack of time is your gain! but hopefully we can both gain! because help! I'm currently located in Portland, OR. Leaving...
  17. Parting Out 1980 CX500 Custom

    Selling and Buying Forum
    Hey everyone. It's been a while since I've been on here. After a lot of thought, I have decided to part out my bike. I just don't ride anymore, and it's taking up a lot of room in my garage. It was fun while it lasted, but I need the money and space, plus I'll be moving cross country soon. I...
  18. 1982 cx500c Parts

    Selling and Buying Forum
    1982 Honda CX500c Parts | street, cruisers, choppers | Winnipeg | Kijiji All parts available. I'll post a parts list after the first part is sold. Will ship anywhere at buyers expense. The bike worked great and the engine ran back in 2013 before it was taken out of the frame and I've got legal...
  19. Parting out my 82 GL500I

    Selling and Buying Forum
    Hello all! I am saddened to say that I have to let my dear old GL500I go. It was mostly in pieces due to varies maintenance tasks and never got back together. I have an entire bike to part out so if you need it, chances are good that I have it. Things I've added to the bike -Aftermarket...
Top